Your 2017-2020 Audi S4 or S5 is the home to a turbocharged 3.0L V6 powerhouse begging to be let loose. IE's performance calibrations unleash your car's full potential right out of the gate. Maximized for incredible power at home on the drag strip and road course while maintaining full comfort and reliability on your everyday commute. Experience IE's Performance ECU Software yourself with a simple install that takes only minutes from the comfort of your own driveway.

EASY POWER
FLASH AT HOME
FASTER IN MINUTES

HARDWARE & FUEL
POWER OPTIONS
MULTIPLE STAGES

ENDLESS FUN
FEATURE PACKED
ENJOY THE DRIVE

LEADING FEATURES

IE Stage 1 & Stage 2 software brings track-ready ECU programming to your turbocharged 3.0L V6 engine while retaining factory comfort and reliability. IE's own tuning technology suite is used to completely reverse-engineer the factory ECU mapping, allowing our software engineers access to realign all safety protocols and sensors for the new performance calibration. Every tune parameter undergoes months of testing on our in-house dyno systems that utilize the world's only Sea Level Generator developed specifically to verify tune operations in any condition. Confidently drive from LA to Pikes Peak with power that will keep you smiling every mile!

Horsepower & torque gains maximized
91, 93, E40, & E85 fuel maps for Stage 1 & 2
Stage 1 for stock hardware or basic bolt-ons
Stage 2 for full bolt-on support
Stage 1 & 2 Plus HPFP for massive mid-range power gains
Stage 1 Transmission Tune included with ECU purchase
Stage 2 Transmission Tune upgrade available
Recalibrated factory boost gauge displays higher boost
Neutral/park rev limit raised to 6500 RPM
Brake boost enabled for rolling launch
Annoying auto-start/stop defaults to off (button turns back on)
More aggressive overrun/crackle in Dynamic mode (Stage 2)
Crackles enabled for free revving in park or neutral
Engine VE is completely remodeled for a smooth power curve
Maximized throttle scaling for dependable throttle use
Boost control reconfigured for smooth and crisp power delivery
Optimized EGT for safe fuel ratios and maximized power output
Eliminated/minimized turbocharger surge
Reduced turbocharger lag
Road speed limiters removed
Engineered for all climates and elevations
Direct port OBDII at-home flashing
Easy octane switching takes only minutes
Read and clear diagnostic/problem codes
Easy to use Data-logger

B9 3.0T STAGE 1

IE Stage 1 ECU calibration dramatically increases performance with up to 505HP & 585TQ, transforming your turbocharged 3.0L into a truly performance-classed vehicle. IE's advanced tuning strategies leave no hidden power on the table and safely max out the factory turbocharger's capability. Engineered to operate on entirely stock hardware and compatible with basic bolt-ons (intake, turbo inlet, intercooler) without the need to retune.

See performance tab for full performance results & dyno reports

B9 3.0T STAGE 2

IE Stage 2 performance software is a complete engine calibration for full bolt-on stock turbo builds running an aftermarket racing downpipe and catalyst. The unique B9 EA839 engines are equipped with a smaller factory turbo and large stock downpipe with incredibly minimal exhaust restrictions. Using advanced calibration techniques, IE calibrators can extract full peak power on pump gas and ethanol fuels on Stage 1 and 2 downpipe setups. However, the required hardware upgrades for stage 2 will increase airflow, lower intake air temps, faster IAT recovery, and produce an overall more efficient and faster vehicle on the same power.

See below for a complete list of Stage 2 hardware requirements

STAGE 1 & STAGE 2 PLUS HPFP

Stage 1 & 2 Plus ECU tunes are calibrated to support increased fuel delivery from upgraded HPFP (High-Pressure Fuel Pump) internals providing additional horsepower and torque through the mid-range of the power band. Acceleration dramatically improves with a 52HP gain in the mid-RPM (peak HP number remains the same) and up to 75ft-lbs of additional torque on E85! Our matching Stage 2+ TCU transmission tune (sold separately) also includes optimized shift points that double down on the intense pull through the middle of the powerband, further increasing acceleration and faster 1/4 mile times.

Stage 1+ & 2+ tunes are included at no additional cost
Requires HPFP upgraded internals with 11.7mm pin size

ETHANOL FUELS

E85 & E40 blend ethanol fuels are included with all stages and unlock the most performance potential from our ECU tunes. Ethanol contains tons of oxygen, burns cooler, and has a high resistance to knock. This provides more horsepower and torque than running conventional gasoline and is much less expensive than race gas.

FULL E85

IE calibrators spent many months developing and testing ethanol blends on the B9 3.0T engines in many climates and elevations. Results were consistent that full E85 runs very close to or beyond the limit of the factory direct injection (DI) fuel system in the mid-range but allows for more power up top. IE's E85 calibration keeps mid-range power in check to avoid lean conditions, misfires, and power loss then ramps it up top for amazingly fast and consistent track times in a drag racing scenario. E85 is also great for easy fill-ups at the pump for daily driving without mixing blends.

E40 BLEND

E40 is an ethanol mix of E85 with regular pump 91/93 fuel creating a lower ethanol content fuel. E40 offers the optimal ethanol content for the factory DI fuel system in the mid-range of the power band. The lower content ethanol allows this file to create the maximum power output from 3000RPM-4000RPM, perfect for road course and track racing. E40 will also result in a faster feeling car in most street driving situations.

An ethanol content sensor kit is highly recommended when running ethanol blends.

BRAKE BOOST

Commonly used in roll racing, Brake Boosting allows you to build extra boost by applying brake pressure while accelerating. Release the brake pressure for a "rolling launch" or extra surge of power.

Brake Boost is included on all tune stages.

EXHAUST OVERRUN

The stock calibration features a very mild overrun/crackle when you decelerate from higher RPM, but is very hard to hear with factory downpipe/exhaust. Stage 2 files turn up the aggressiveness of this overrun and enable crackles on free-revving in neutral or park. Not only will your car drive faster, it will sound faster too! Guaranteed to put a smile on your face.

Exhaust Overrun is included on stage 2 tunes.

BOOST CONTROL

The stock ECU boost control is delivered in a very “close enough” and erratic boost curve. This slow response is reflected in the factory torque curve and can be felt on long power pulls when utilizing the entire powerband. To smooth out this torque curve, IE calibrators re-tuned the boost control mapping to be much faster achieving precision boost request targeting that results in unmatched power delivery.

THROTTLE MAPPING

The new generation Audi MG1 ECU uses a complicated mass flow model to calculate boost control. Typical ECU tunes simply raise the wastegate pressure, however, since the maps that control wastegate position (boost) are not controlled by throttle input resulting in limited throttle predictability. To avoid delivering full-boost at half throttle input, IE engineers have taken the care to rescale the entire mass flow model mathematically over 30 maps which correct the entire range of throttle input. This delivers a linear and predictable throttle pedal which improves drivability in every situation on the street or track.

EGT OPTIMIZATION

Exhaust Gas Temperature (EGT) is the measurement of fuel mixtures exiting the exhaust and is used to determine the health of the fuel/air mixture entering the engine. IE engineers have spent countless hours adjusting boost air/fuel ratio, ignition timing angle, camshaft phasing, intake air temps, and much more to develop the proper EGT adjustments for ultimate engine safety without sacrificing power on all octanes. Since Ethanol burns cooler than gasoline, the extra fuel left over in the cylinders acts as coolant further reducing combustion temperatures and allows for a leaner air to fuel ratio without dangerous EGT levels. All IE files contain safety measures and complete knock control to keep the engine producing its potential within verified and safety-first operation.

RECALIBRATED VE

The factory engine calibration shows a significant drop in torque and power around 3000 RPM due to the unique volumetric efficiency (VE) of the stock 3.0T engine. Instead of tuning around this drop in VE or attempting to simply raise the factory torque/load maps to compensate, our calibrators have completely solved and removed this drop from our ECU calibrations entirely.

IE's dyno charts are ported directly from our in-house dyno cells and are not modified or "smoothed" in any way.

UPGRADING STAGES

Upgrading from Stage 1 to Stage 2 or Stage 3 is easy! With IE, you only pay the difference in tune cost with no extra fees. When you install the required matching hardware, simply follow the link on your IE POWERlink software to purchase the tune upgrade and you will be enjoying the next level of power in minutes!

HARDWARE GUIDE

STAGE 1 COMPATABILITY

PART UPGRADE	COMPATIBLE	REQUIREMENT
STAGE 1 TCU TUNE (INCLUDED)		Required
STAGE 2 TCU TUNE		Highly recommended
AIR INTAKE		Highly recommended
TURBO INLET PIPE		Fully compatible with all stages
INTERCOOLER		Fully compatible with all stages
HPFP UPGRADE		Use with Stage 1+ only
CATBACK EXHAUST		Fully compatible with all stages
DOWNPIPE	X	Not Compatible With Stage 1

STAGE 2 COMPATABILITY

PART UPGRADE	COMPATIBLE	REQUIREMENT
STAGE 1 TCU TUNE (INCLUDED)		Required
STAGE 2 TCU TUNE		Highly recommended
DOWNPIPE		Required
AIR INTAKE		Highly recommended
TURBO INLET PIPE		Highly recommended
INTERCOOLER		Required
HPFP UPGRADE		Use with Stage 2+ only
CATBACK EXHAUST		Fully compatible with all stages

DOWNPIPE NOTICE: BY PURCHASING A MOTORSPORT/RACING PRODUCT ("PRODUCT"), YOU REPRESENT THAT YOU UNDERSTAND AND AGREE THAT: THE PRODUCT IS NOT DESIGNED TO MEET ANY APPLICABLE EMISSIONS STANDARDS, WHETHER IN THE USA OR OTHERWISE, THE PRODUCT IS NOT C.A.R.B. COMPLIANT, AND THAT THE PRODUCT IS NOT FOR SALE OR USE IN CALIFORNIA, USA NOR ANY OTHER JURISDICTION WHERE THE SALE OR USE IS PROHIBITED BY LAW. INTEGRATED ENGINEERING, LLC MAKES NO REPRESENTATIONS, WARRANTIES, OR CLAIMS THAT THIS PRODUCT COMPLIES WITH ANY APPLICABLE EMISSIONS LAWS AND EXPRESSLY DISCLAIMS ANY AND ALL SUCH REPRESENTATIONS, WARRANTIES, AND CLAIMS, WHETHER EXPRESS OR IMPLIED. BY PURCHASING THIS PRODUCT, YOU REPRESENT, WARRANT, AND AGREE THAT IT IS YOUR RESPONSIBILITY TO INFORM YOURSELF OF ANY LAWS OR REGULATIONS THAT MAY APPLY TO YOUR PURCHASE AND/OR USE OF THE PRODUCT.

" This tune is ridiculous
-Mark S.

" Game changer
-Gage K.

" My S4 is now a monster
-James B.

LEADING FEATURES

The IE Stage 3 and Stage 3 Plus TTE710 race suite produces up to 715HP with the ability to pound out 9-second quarter-mile passes and transform your mild-mannered sedan into an exotic-destroying performance machine. Enjoy minimal turbo lag, a massive power band, incredible transient response, and torque that pulls like a freight train! Our complete hybrid turbo tuning suite will deliver massive performance on demand without sacrificing an ounce of daily comfort or spending the kid's college fund on a costly race engine build. Using simple bolt-in hardware and our Stage 3 ECU tuning, get ready to experience true racecar power without compromise!

Up to 715HP & 678TQ
Complete TTE710 hybrid turbo tuning suite
91, 93, & 104 fuel maps for Stage 3
91, 93, 104, E30 & E70 fuel maps for Stage 3 Plus
Stage 3 for stock fueling and Stage 2 hardware
Stage 3 Plus with 4 bar MAPs, HPFP, and injector upgrade
Optimized safely for factory engine internals
Massive power increase throughout the powerband
Builds power higher into the RPM range
Includes catered tune verification with IE calibrator
Massive top-end power with minimal boost lag increase
Engineered with high-end motorsport sensor strategies
Neutral/park rev limit raised to 7000 RPM
Brake boost enabled for rolling launch
Factory boost gauge displays the higher boost
Aggressive overrun/crackle in sport mode (can be disabled)
Crackles enabled for free-revving in park or neutral
Road speed limiters removed
Annoying auto-start/stop defaults to off (button turns back on)

CATERED TUNE VERIFICATION

This is an advanced ECU calibration that delivers BIG power numbers, taking a responsible tuning approach; every TTE710 Stage 3 or Stage 3 Plus purchase includes and requires a catered introduction with an IE calibrator. During this quick process, your existing or new hardware setup will be verified to ensure proper compatibility before flashing the file. Once the tune is applied, our calibration team will then walk you through an easy logging process where your own engine data will be obsessively reviewed and confirmed for proper operation and safety parameters. Prepare for a truly exhilarating driving experience knowing IE has your back.

Stage 3 files will not show available on your IE POWERlink for flashing until the verification process is started. To begin, simply contact tuning@performancebyie.com after purchase.

STAGE 3 TTE710

IE Stage 3 TTE710 offers an easy upgrade into hybrid turbo power levels delivering up to 601HP and 615TQ from pump fuel (91, 93, or 104 octanes) with only the turbocharger upgrade along with stage 2 hardware (intake, turbo inlet, intercooler, & downpipe). This setup delivers deceivingly fast performance on stock MAP sensors and without additional fueling upgrades.

See performance tab for full performance results & dyno reports

STAGE 3 PLUS TTE710

IE Stage 3 plus is for those looking to smash the competition with the maximum power output available from the hybrid turbocharger. This blistering fast calibration requires additional hardware upgrades to increase fueling support for even more power from pump gas and unlocks ethanol blends. Using an upgraded HPFP (high pressure fuel pump) and TTE 4 bar map sensors for up to 642HP and 638TQ on E30 ethanol blend. Or go all out with a truly exhilarating 715HP and 678TQ with upgraded fuel injectors and E70 ethanol blend!

PART UPGRADE	REQUIREMENT	INFO
HPFP UPGRADE	Required	11.7mm pin diameter minimum size
TTE 4 BAR MAP SENSORS	Required	Available here
4.0TT RS INJECTORS (X6)	Required for E70 ethanol	Audi part number: 06M906036AD

See below for a complete list of Stage 3 & Stage 3 Plus hardware requirements

IE STAGE 3 TTE710 TCU TUNE

IE Stage 3 and Stage 3 Plus far exceed the factory set transmission torque limit while delivering more power across the entire powerband and holding that power further into the higher RPM range. These performance enhancements require a complete matching transmission control unit (TCU) calibration. IE Stage 3 TTE710 TCU Tune fully harmonizes the complete drivetrain for the hybrid turbo characteristics with optimized shift points, further increased RPM limits, faster shift speed, user-selectable launch control, new drive-mapping, and more.

Stage 3 TTE710 TCU Tune is a free upgrade from Stage 2 TCU

STAGE 3 + ETHANOL BLENDS

Stage 3 Plus utilizes 4-bar MAP sensors and an HPFP upgrade to open the fueling potential for the E30 ethanol blend for a massive jump in power over pump gas. Upgrade your fuel system with optional 4.0TT RS injectors for a higher E70 blend and the track-destroying 715HP! E30/E70 is the highest blend safely available within the fuel system limitations delivering the maximum performance numbers without pulling power for higher E%. Ethanol content must not exceed E70 of the required blend; an ethanol content sensor kit and gauge are highly recommended.

Stage 3 Plus and required hardware upgrades required for ethanol use

TTE710 HYBRID TURBO

IE engineers and calibrators valued fast boost response, top-end power, and a robust build when selecting a turbocharger as the base for our Stage 3 tuning. After extensive research and testing, the clear winner by a long shot was the advanced design of the German-made TTE710 from The Turbo Engineers. This hybrid turbo is a direct bolt-in replacement that provides a unique combination of big top-end power and responsive boost with very minimal lag. When combined with IE's calibration strategies, the result is a perfect marriage of modern vehicle tech and raw chest-pounding performance.

TURBO SOLD SEPERATELY

GET ONE

TTE710 TUNE DEVELOPMENT

REAL WORLD TESTING

At every stage of tune development, the results were dyno tested, street verified, pushed on the track, and expanded to a beta testing community. This verification process provides a library of data from various vehicles, fuels, climates, weather conditions, and altitudes, all used to make numerous changes to the files to maximize performance, driving characteristics, and reliability in any situation. In one of these track tests, an early TTE710 tune variant set the B9 3.0T world record and became the official first B9 3.0T in the 9s!

ENGINE MANAGEMENT

Stage 3 horsepower is a serious amount of power for any engine. To keep the stock engine internals safe under these extreme power levels, IE calibration and software engineers employed highly advanced tuning practices and equipment to develop a complete ground-up engine management system within the factory ECU. Extensive mapping rework was performed to support the TTE710 and verified in thousands of complete powerband pulls in our dyno cells and countless hours of testing every tune iteration on the street and track. All performance calibrations and safety coding has been rewritten and converted to run with the substantial power gains from the large hybrid turbocharger.

ADVANCED R&D

To properly configure the ECU, IE's engineers installed a variety of additional sensors and probes throughout the engine to record critical data that is not available via the factory equipment. This is an expensive and tedious process; however, the information gathered is priceless when calibrating the ECU for the new hardware specifications. The added sensors record cylinder pressures, EGT, exhaust pressure, mass airflow, and more for a high-resolution log of important turbo and engine operating parameters.

MAPPING STRATEGY

The advanced software development strategies provide the confidence to responsibly build a calibration suite for peak power output without relying on risky modeled information or guesses for engine and drivetrain safety. Hundreds of maps have been defined and calibrated from a ground-up approach to create a fully rounded software suite designed to deliver professional motorsport quality performance while improving everyday driving characteristics beyond factory programming. The result is more than adjusted stock tune mapping and delivers a true TTE710 engine management system completely realized within the factory ECU.

COMPRESSOR EFFECIENCY

One of the countless important examples of this advanced programming is the development of the factory wastegate/boost pressure control mapping. The MG1 ECU contains a sophisticated model with many inputs used to ensure proper engine safety adaptations for any operating condition or climate; the compressor efficiency of the larger turbo drastically alters this model. Instead of tuning around these shortcomings with compromises, IE's calibration team expanded the map structure specifically to the TTE710 from the ground up, ensuring proper drivability, perfect boost control, safe boost regulation, and guaranteed consistency in all driving conditions.

WASTEGATE PREDICTED STROKE

The vast difference in wastegate flow and response with the TTE710 compared to the stock turbo provides another extreme example of a situation where the factory mapping has been completely disregarded and replaced with an entirely new strategy. Significant time has been invested in perfecting every input affecting this system resulting in a map that has taken on an entirely different shape matching the characteristics of the hybrid turbo's boost control. This thorough calibration process is the result of many months but delivers unparalleled power delivery and reliable power at any throttle input beyond even the factory feel.

BRAKE BOOST

Brake Boosting provides a competitive edge in a roll racing scenario by using brake pressure to build boost at speed resulting in a rolling launch.

Brake Boost is included on Stage 3 & Stage 3 Plus

EXHAUST OVERRUN

Stage 3 files include optional exhaust overrun/crackles for an aggressive motorsport sound during decel or free-revving in neutral or park. The feature is enabled in sport mode only and can be disabled by setting drive select to comfort, or toggling engine sounds to comfort in individual mode.

Exhaust Overrun is included on stage 3 and Stage 3 Plus.

STAGE 3 HARDWARE GUIDE

STAGE 3 TTE710 REQUIREMENTS

PART UPGRADE	COMPATIBLE	REQUIREMENT
STAGE 3 TCU TUNE		Required
TTE710 HYBRID TURBOCHARGER		Required
DOWNPIPE		Required
AIR INTAKE		Required
TURBO INLET PIPE WITH TTE710 ADAPTER		Required
INTERCOOLER		Required
CATBACK EXHAUST		Fully compatible with all stages

STAGE 3 TTE710 PLUS REQUIREMENTS

PART UPGRADE	COMPATIBLE	REQUIREMENT
STAGE 3 TCU TUNE		Required
TTE710 HYBRID TURBOCHARGER		Required
HPFP UPGRADE		Required
TTE 4 BAR MAP SENSORS		Required
(X6) 4.0TT INJECTORS 06M906036AD		Required for E70 ethanol
DOWNPIPE		Required
AIR INTAKE		Required
TURBO INLET PIPE WITH TTE710 ADAPTER		Required
INTERCOOLER		Required
CATBACK EXHAUST		Fully compatible with all stages

HARDWARE RECOMMENDATIONS

AIR INTAKE SYSTEM

The larger turbocharger requires increased airflow from an upgraded air intake system. Additionally, the TTE710 has an increased 66mm turbo inlet size at the compressor requiring a matching aftermarket turbo inlet. IE intake and turbo inlet are recommended to make the installation process of your new hybrid turbo a simple bolt-in job. Our cast turbo inlet design utilizes a CNC-machined adapter to fit the TTE710 without hassle while maintaining the largest size possible for zero flow restrictions.

IE INTAKE SYSTEM & TURBO INLET PIPE PICTURED WITH TTE710 HYBRID TURBO & IE CAST DOWNPIPE

INTERCOOLER

With power comes heat; upgrading your intercooler is crucial for both performance and safety on TTE710 Stage 3 power levels. Our IE FDS Intercooler upgrade is highly recommended to provide the lowest IATs from unique design features and proven charge-air cooling capability.

DOWNPIPE UPGRADE

The factory-equipped downpipe cannot support the power levels provided by IE's Stage 3 race suite and the hybrid turbo's exhaust flow rate; a performance aftermarket downpipe is required. Our TTE710 development vehicle was equipped with this downpipe in our world-first 9-second B9 3.0T quarter-mile run. Our IE Cast Catted Downpipe Kit provides a direct-fit install with the hybrid turbo.

MAXIMIZED OUTPUT

IE ECU calibrations are dedicated to perfecting every section of the mapping to deliver a fully realized performance file right out of the gate. Maximized for full performance potential on the drag strip and road coarse while maintaining full comfort and reliability on your daily commute. Get ready to experience IE's Performance Software For your Audi S4, S5, or SQ5 in only minutes from the comfort of your garage or driveway.

POWER GAINS

North American Region (NAR) = AKI / Rest Of World (ROW) = RON

STAGE / FUEL	HORSEPOWER	TORQUE
Stock Audi advertised numbers	349 HP	369 FT-LBS
Stock IE dyno numbers	346 HP	412 FT-LBS
Stage 1 & 2 91 AKI / 95 RON	427 HP	530 FT-LBS
Stage 1 & 2 93 AKI / 98 RON	446 HP	548 FT-LBS
Stage 1 & 2 E85	505 HP	587 FT-LBS
Stage 1 & 2 E40	484 HP	603 FT-LBS
Stage 1 & 2 Plus HPFP 91 AKI / 95 RON	427 HP	546 FT-LBS
Stage 1 & 2 Plus HPFP E85	505 HP	650 FT-LBS
Stage 3 91 AKI / 95 RON	534 HP	547 FT-LBS
Stage 3 93 AKI / 98 RON	557 HP	565 FT-LBS
Stage 3 104 AKI / 108 RON	601 HP	615 FT-LBS
Stage 3 Plus 91 AKI / 95 RON	566 HP	581 FT-LBS
Stage 3 Plus 93 AKI / 98 RON	578 HP	596 FT-LBS
Stage 3 Plus 104 AKI / 108 RON	625 HP	632 FT-LBS
Stage 3 Plus E30	642 HP	638 FT-LBS
Stage 3 Plus W/injectors 91 AKI / 95 RON	566 HP	581 FT-LBS
Stage 3 Plus W/injectors 93 AKI / 98 RON	578 HP	596 FT-LBS
Stage 3 Plus W/injectors 104 AKI / 108 RON	625 HP	632 FT-LBS
Stage 3 Plus W/injectors E70	715 HP	678 FT-LBS

Dyno numbers are for reference against stock numbers only. Personal dyno results will vary depending on fuel quality, local conditions, dyno brand, and correction factors.

DYNO CHARTS

" This thing is a beast
-Matthew W.

" Massive acceleration
-J. Smith

" Unbelievable
-Hank D.

TCU TUNE REQUIRED

IE ECU tunes unlock massive horsepower and torque gains that exceed the torque limitations of the stock transmission calibraiton which triggers the TCU to limit power output.
To solve this, a matching transmission TCU tune is required.

STAGE 1 TCU

(Included at no cost)

IE's stage 1 TCU tune raises the torque limits of your AL552 ZF8 automatic transmission to allow the power gains from IE ECU Tunes. Stage 1 fully realizes all available performance from the IE ECU Stages while keeping all transmission driving characteristics otherwise stock.

Stage 1 TCU tune is included with all B9 3.0T ECU calibrations at no extra charge.

STAGE 2 TCU

(Sold separately)

IE's stage 2 TCU tune offers further performance calibraitons that deliver raised torque limits, faster shifts, optimized shift points, multiple launch-control modes, enthusiast drive mapping, and more! When paired with an ECU tune, Stage 2 TCU will significantly transform every performance aspect of your B9 3.0T delivering faster launches, higher Gs, and further improved acceleration.

Stage 2 TCU is a perfect match for Stage 1 & Stage 2 ECU Tunes

LEARN MORE

STAGE 2+ TCU

(For Stage 1+ / Stage 2+ HPFP Tunes )

specifically designed for IE Stage 1+ or Stage 2+ HPFP ECU tunes, the Stage 2+ TCU file includes all the same performance features as Stage 2, but with new optimized shift points to keep the engine in the higher output powerband seen from the HPFP specific calibrations. This shift strategy will significantly improve acceleration and quarter-mile times on the track.

Stage 2+ TCU tune is included with Stage 2 TCU purchases at no extra charge.

STAGE 3 TCU

(For IE Stage 3 TTE710 Hybrid Turbo)

IE Stage 3 and Stage 3 Plus ECU tunes deliver massive power gains across the entire powerband and further into the higher RPM range. These performance enhancements require a complete matching transmission calibration. IE Stage 3 TCU Tune is the matching transmission calibration for the hybrid turbo with optimized shift points, further increased RPM limits, and new drive-mapping. This tune is provided as a free upgrade from Stage 2 TCU Tunes when upgrading to Stage 3 TTE710 ECU.

Stage 3 TCU tune is unlocked with purchase of Stage 3 TTE710 ECU purchases

TCU TUNE FEATURES

FEATURE	STAGE 1 TCU	STAGE 2 TCU	STAGE 3 TCU
Increased torque limits
Enthusiast performance mapping	X
Faster shift speeds	X
User-adjustable variable launch control	X
Enabled launch control in all drive modes	X
Optimized shift RPM by gear	X
Raised RPM limit in manual mode	X
Enabled 1st gear downshift without coming to stop	X
Faster shift speed for double-downshifting	X
Stage 1 & Stage 2 ECU support			X
Stage 3 ECU hybrid turbo support	X	X

EASY INSTALL FROM HOME

IE's POWERlink Cable and Flash Wizard software gives you the freedom to quickly flash your new IE ECU Tune. Simply plug your POWERlink into the vehicle's OBD-2 port and follow the on-screen directions, it's that easy!

Expand the buttons below for more details on these features

DIRECT PORT

The IE POWERlink is a powerful direct-port tool that plugs directly into your vehicle's OBD-2 terminal. This grants instant access to flash and upgrade tune stages, switch fuel octanes, turn on/off features, flash back to stock, perform engine diagnostics, and record logs with the built-in data logger from the comfort of your own driveway.

OCTANE SWITCHING

All IE B9 3.0T stages include multiple octane options. Using your IE Powerlink, you can easily switch between calibrations for different fuels and unlock different power levels. Depending on the Stage, choose from 91, 93, E40 and E85.

UPGRADE STAGES

Your POWERlink cable allows you to upgrade stages for matching hardware, switch between them, and flash back to stock as you need. Once you purchase a stage you also own all of its features, octanes, and any stage under it.

TOGGLE FEATURES

Simply plug-your IE POWERlink to quickly turn on optional features such as the included exhaust crackle. The process is the same as adding a tune and can be turned off just as easily.

CODE READER

Pesky check engine light turn on? Save a trip to the shop and use your IE POWERlink to diagnose the problem. The easy to use code reader will pull up any trouble codes and once the issue is fixed, clear the code and get back to the fun.

DATA LOGGER

Verify the healthy operation of your engine using the built-in data logging function. Nothing is better than a piece of mind that your investment is operating optimally. First time data logging? This article will help show you the ropes: How To Data Log

FITMENT GUIDE

MAKE	MODEL	YEAR	GENERATION
AUDI	S4	2017-2020	B9
AUDI	S5	2018-2020	B9
AUDI	SQ5	2018-2020	B9

CONSUMER NOTICE: All IE tunes are currently listed for B9 model years only, B9.5 (2021+) models are not currently supported. B9.5 support is coming soon!

" The flash install was super easy
-Jackson

" Extremely user friendly
-Matt R

" You won’t regret it
-Andres

IMPORTANT INFORMATION

TUNE UPDATES
Your tune purchase entitles you to free updates to any tune revisions, new octanes, standard features, or software updates. In the event the original vehicle manufacturer issues an ECU update, this will also be included to you through IE at no additional charge.

POWERLINK VINS
Have multiple cars in the family or friends that are also ready for an IE Tune? Your POWERlink Flash Tool can be used on up to 5 different vehicle VINs. Tunes sold separately.

TUNE REGISTRATION
Once a tune purchase is applied to your vehicle's ECU, the tune is permanently registered to the vehicle and non-transferable to other vehicles. Tunes can be transferred to a second party in the event of vehicle transfer of ownership only.

REQUIRES V4 IE POWERLINK
The Audi MG1 uses new and updated flashing protocols to read and write the ECU and TCU information. Older V3 IE POWERlinks do not include the required internal hardware need to flash the B9 2.0T calibrations. If you are purchasing credits with an existing IE POWERLINK, please be sure your serial number on the back begins with V4.

ENGINE SPECS


ENGINE FAMILY	EA839
CYLINDERS	6
INDUCTION	Turbocharged
DISPLACEMENT	3.0L
ORIENTATION	Longitudinal
FUEL	Gasoline (AKI / RON) & Ethanol (tuned only)
AVAILABILITY	North America (NAR) & Rest of World (ROW)

PRICING GUIDE

PRODUCT	PRICE
POWERlink Flash Tool	$149.99
IE EA839 3.0T Stage 1	$899.00
IE EA839 3.0T Stage 2	+$100.00
IE EA839 3.0T Stage 3	+$100.00
IE EA839 3.0T Stage 3 Plus	+$300.00
IE AL552 Stage 1 TCU Tune	Included with stage 1 & stage 2 ECU
IE AL552 Stage 2 TCU Tune	+$699.00
IE AL552 Stage 3 TCU Tune	Included with stage 2 TCU

POWERLINK SYSTEM REQUIREMENTS

DEVICE	PORTS	OS	PROC.	POWER	RAM
Laptop or Tablet	Wifi & USB	Windows 7 or newer	32 or 64 bit	1.0ghz or greater	4GB or greater

DOWNLOADS

FILE	SYSTEM	SIZE	DOWNLOAD
IE Flash Wizard Setup	Windows 7 or newer	799kb

FIVE-STAR SUPPORT

IE's number one goal from purchase to installation is to provide you with the best customer experience in the industry. We want what you want; a simple purchase process, products that exceed expectations, and a brand that's got your back. If at any point you have any questions, need help, or require support with your new tune our educated customer support team and tuning specialists are standing by and happy to help. Purchasing an IE tune not only guarantees a quality product, but that you will always have us in your corner.

Live Fast, Buy Fun

Having some trouble? Don't worry, our team of tuning specialist are here to help. Fill out the form on our Support Page to start a ticket.

" Customer service is second to none!
-Zach

" Earned a customer for life
-Brenton

" A+++
-Sonny T